Repairing SERVICE CODE FOR WASHING MACHINE

DAEWOO WASHING MACHINE ERROR CODES FOR MODEL#ED1232

Daewoo DWC-ED1232 washer error codes

PROBLEMCHECK POINT
The washer will not operate at all.• Is there a power failure?
 • Is the power cord correctly connected to an electric outlet?
 • Did you turn on the power?
 • Did you press Start/Hold button?
 • Is there correct amount of laundry in the washer?
Water is not supplied. Error display IE• Did you connect the inlet hose and open the water tap?
 • Is the inlet hose or the water tap frozen?
 • Is the water supply shot off?
 • Is there any foreign matter blocking up the inlet hose filter?
The washer will not drain. Error display OE• Is the drain hose frozen or blocked up by dirt?
 • Is the drain hose kinked or deformed?
 • Is the end of the drain hose immersed in water?
 • Is there excessive dirt inside the drain filter?
The washer will not spin. Error display UE• Is the clothes in the drum collected on one side?
 • Is the washer installed on an uneven floor or is the vibration serious?
 • Is the door open? (The lamp “Hi” will light up in this case.)
The washer will stop during spinning. Spinning is insufficient.Error display PFE• Is the filter of the drain pump clogged?
 • Is the drain pump operated?
 • Did you use the proper amount of detergent?
 • Is the drain hose placed higher than 1m above floor?
Vibrating and too noisy• Is the washer installed on an uneven floor?
 • Have all the transit bolts removed?
E8 and E9If this error mode are showed on PCB board, please contact service center.
Daewoo DWD-F1011 washer error codes
ERROR MESSAGEIndicator Light twinkling Indicator Light twinkling Indicator Light twinkling
 Start/HoldIntensive washRinse+Rinse Hold
IExx  
PFE, OE, E4x x 
E7, E8x  x
E2, E9xxx 
H2, H4, H5, H6, H8xx x
UEx xx
LExxxX
MESSAGEERRORCAUSESOLUTION
IEWATER INLET ERRORThe water tap is closed.Open the water tap.
  The filter of the valve inlet is clogged.Clean the filter of the valve inlet.
  The valve inlet is an inferior product or broke down.Change the valve inlet.
  The water level sensor (sensor pressure) is an inferior product or broke down.Change the water level sensor (sensor pressure).
  The drain motor works during water supply.Change the drain motor.
  The PCB ASS’Y does not check the water level.Change the PCB ASS’Y.
OEDRAIN ERRORThe drain hose is kinked or clogged.Clean and straighten the drain hose.
  The drain motor is an inferior product.Change the drain motor.
  The valve inlet works during drain.Change the valve inlet
UEUNBALANCE ERRORThe laundry is concentrated to one side of the drum during spin.Rearrange the laundry.
LEDOOR OPEN ERRORThe Start/Hold button is pressed while the door is opened.Close the door.
  The switch door lock is an inferior product.Change the switch door lock.
  The PCB ASS’Y does not check the door lock.Change the PCB ASS’Y.
E2OVERFLOW ERRORThe water is supplied continuously due to an inferior valve inlet.Change the valve inlet.
  The valve inlet is normal, but the water level sensor (sensor pressure) is inferior.Change the water level sensor (sensor pressure).
  The drain motor dose not work. (The drain motor is an inferior product or broke down.)Change the drain motor.
E4LEAKAGE ERRORWater leaks from the tub or the hose drain.Check the leak of the tub or the hose drain. Then change the tub or the hose drain.
E5HIGH VOLTAGE ERRORThe laundry is jammed between the gasket and the drum.Rearrange the laundry.
  The PCB ASS’Y is an inferior product.Change the PCB ASS’Y.
E6EMG ERRORThe laundry is jammed between the gasket and the drum.Rearrange the laundry.
  The motor is an inferior product.Change the motor.
  The PCB ASS’Y is an inferior product.Change the PCB ASS’Y.
E8MOTOR ERRORThe motor is not normally connected.Check the connector of the motor.
  The motor does not work. (The motor is an inferior product or broke down.)Change the motor.
E9SENSOR PRES- SURE ERRORThe water level sensor is an inferior product.Change the water level sensor.
H2THERMISTOR WASH ERRORThe thermistor wash is an inferior product or broke down.Change the thermistor wash.
  The thermistor wash is not connected normally.Check the connector of the thermistor wash.
H4THERMISTOR WASH OVERHEATING ERRORThe heater worked without the water in the tub.Check the water level.
  The thermistor wash is an inferior product or broke down.Change the thermistor wash.
H5WATER TEMP. ERRORThe water temp, is over 45°C in delicate & wool course. (The thermistor wash is an inferior product or broke down.)Change the thermistor wash.
H6HEATER WASH ERRORThe heater wash dose not work.Change the heater wash.
  (The water temp, doesn’t rise over2°C during 15min.) 
H8HEATER WASH OVERHEATING ERRORThe heater worked without the water in the tub.Check the water level and the heater wash.
lbIGBT ERRORThe PCB ASS’Y is an inferior product.Change the PCB ASS’Y.
PFEPUMP FILTER ERRORThe drain pump filter is clogged.Clean the drain pump filter.
  The drain pump does not work during spin.Change the drain pump.
  The large amount of detergent was used.Use the proper amount of detergent.
  The drain hose is placed higher than 1 m above the floor.Place the drain hose 1 m below the floor

Advice: If the fault remains, we recommend you call Us for service on:
+965 66398651
+965 94942300

Whats App Direct Link: – http://Wa.me/+96566398651 Whats App group Link: – https://chat.whatsapp.com/CGmau68tmrII4jEYpI8XlN

Leave a Comment

Your email address will not be published.

You may also like