Blinking Codes PDF-DOC

Sony LED TV Blinking Codes

Many of the later model Sony TV’s have a built in Self- Diagnosis function. If

the timer/standby indicator is blinking, this could be an indication of the

Problem with the unit. The diagnostic blinking will occur automatically with no

action required by you to engage it.

The timing of the blinking you see would be as follows: two to eight blinks

(Depending on the fault) about a third of a second apart, then pauses for 3

seconds, then the two to eight blinks about a third of a second apart again.

Here is a list of the problems that might have occurred indicated by the

number of blinks. The words in parentheses are those which you will see for

each of these faults on a diagnosis screen described later in this article.

  • Unit is dead and there are no blinks—Problem in the standby power

section. Might check fuse, R607, Q601, IC601, R612 and VDR601 (should

show open)

  • Continuous Blink Once A Second, No Pausing As Discussed Above

No reply from the jungle IC301 (data bus is busy, shorted to ground or held

high), IK video path is defective.

  • ONE Blink— not used for the self-diagnosis
  • TWO Blinks-–B+ over current protection (OCP) , unit goes to the standby

mode then displays the 2 blink fault. Could be a short in the power supply of

any of the circuits.

  • THREE Blinks—B+ over voltage protection (OVP), unit goes to the standby

mode then displays the 3 blink fault. This is also a problem in the power

supply circuit, check T603 and R672.

  • FOUR Blinks—No Vert. Deflection (V STOP), Screen goes to a single

horizontal line then the video signal muted. Check IC1509, Q1505

  • FIVE Blinks—AKB circuit (AKB), the timer/standby indicator blinks for about

30 seconds then goes to the self-diagnosis function. Something is wrong with

the video. Check video out, Q705, 732, 761 and other components on the C

board, also check Q218, 219, 220 on the A board. Also unit be in IK blanking,

try turning up screen slightly.

  • SIX Blinks—No Horizontal (H STOP), no raster, goes to the blinking self-diagnosis function immediately. Check C515 & 516 and the jungle IC, IC206.
  • SEVEN Blinks—High voltage shutdown. The high voltage has exceeded 33k

and the unit goes immediately into safety shutdown. Check power supply

regulation and horizontal circuits.

  • EIGHT Blinks—Problem with the audio (AUDIO), unit goes to standby and

blinks the self-diagnosis code. Check IC406 audio amp, PS401 and 402.

  • Intermittent problems?? This is a great feature. You can also bring up

these fault codes ON-SCREEN to see a list of the problem numbers with the

abbreviation of the problem and the number of times this problem has

occurred. This is slightly different than entering the service mode. To see the

diagnostic screen, Press the following buttons:

  • Display, Channel, 5, Vol Minus, ( Not plus ) then Power. This brings up

a screen with a list of the problems and number of times they have occurred.

Each of the problem names is abbreviated as, “OCP”, “OVP”, “V STOP”, ETC.

We have repeated them in parentheses in the text for the “Blinks” described

above so you can correlate between the diagnostic screen and the blink

codes.

So, now that you know about these self-diagnostics, how do you use them?

Say that you have a set with a black screen. You see that the LED is blinking

4 times….This would tell you that you have no vertical and that is why the

video is muted. If it was blinking 6 times, you would know that you have a

horizontal fault.

It’s not a sure cure, but it’s a little better than a poke in the eye with a sharp

stick.

IMPORTANT: after you repair the unit, PLEASE clear the values on this

diagnostic screen. These codes do not reset themselves after the fault is

corrected, so if you don’t clear them, you’ll be seeing “old” fault codes the

next time you enter this screen.

Clearing is done by going into the service mode ( display, channel, 5,

volume plus, then power ) then press 8 and Enter, which of course returns

everything to the factory preset condition.

Advice: If the fault remains, we recommend you call Us for service on:
+965 66398651
+965 94942300

Whats App Direct Link: – http://Wa.me/+96566398651

Whats App group Link: – https://chat.whatsapp.com/CGmau68tmrII4jEYpI8XlN

Leave a Comment

Your email address will not be published.